Loading... Please wait...

XTREME MJ survives Hurricane Irma! Read one customer's experience (September 2017):
"We've owned a Bad Boy (Xtreme) MJ for about 3 years now, and it has been a highly valuable device on board. We've got it installed at the top of the mast, riveted in on the provided L bracket. We are located in St Maarten where we recently took a huge Category 5 direct hit with over 200MPH/360KPH winds. I'm happy to report the Bad Boy, with antenna, is still mounted at the top of the mast. Suffice to say, your product is pretty robust. Thanks again!" - Derek, s/y ARAVILLA

If you can find a better price for a complete system similar to Xtreme, we will better it by 10%!
Practical Sailor "We think it’s a good value for a high-quality product"   Read...
  • Rail / Flat Surface Mounting Kit
  • Mount Installed
  • Xtreme Installed with Rail Mount
  • Xtreme Flat Surface Mounted at Masthead

Rail / Flat Surface Mount

$34.95

Product Description

The Rail / Flat Surface Bracket Mount allows for a variety of installation options for the BAD BOY Xtreme and Antenna. Can be used for both rail installation and flat vertical surfaces.

The hole configuration allows for almost unlimited angle options to ensure vertical alignment of antenna, whether on a rail or attached to a flat surface. The non marring nylon rail adapters are designed for easy attachment to 7/8" - 1" tubing. These injection molded adapters allow for positive attachment without scratching or marring tubing.

Includes

  • Stainless steel bracket
  • Nylon mounting adapters
  • Stainless steel screws and nuts

 

Warranty Information

1. All Bitstorm products are warranted against defects in material and workmanship for a period of one year from date of purchase under normal use. Warranty does not cover damage caused as a result of improper installation.
2. The customer is responsible for delivering the defective product to the designated RMA address for repair or replacement.
3. At its discretion, Bitstorm will repair or replace a product that was found to be defective by Bitstorm during the warranty period.
4. This warranty does not cover labor cost for removing and reinstalling the device for repair nor for any expendable parts that are readily replaced in normal use.
5. The sole responsibility of Bitstorm under this warranty shall be limited to repair of this product, or replacement thereof, at the sole discretion of Bitstorm.
6. All RMA items shipped to Bitstorm must be freight prepaid. Bitstorm will pay the return freight via a service of Bitstorm's choice. Customer is responsible for payment of any shipping upgrades.

Limitation of Warranty
This warranty does not apply if product:
a. has been opened and/or altered, except by Bitstorm technical personnel,
b. has been painted in way shape or form,
c. has been damaged due to errors or defects in customer provided cabling,
d. has been subjected to abnormal physical or electrical stress, including lightening strike, misuse, negligence or accident,
e. has been improperly installed, including wiring errors or damage done to cable during installation,
f. failure to apply supplied dielectric grease to device connector,
g. has had removal of MAC address label (if one was affixed), or
h. has been loaded with incorrect firmware or attempted to have incorrect firmware loaded.
What information will be required?
1. Customer name, contact information, and shipping information.
2. Date and location of purchase (we may request a copy of the invoice as proof of purchase in certain, limited circumstance).
3. Problem description.
4. MAC address of each unit (if available).
5. Troubleshooting actions taken so far.

*** International Customers ***
1. Customer to use their own shipping account when sending products back to Bitstorm.
2. When sending back RMA, the commercial invoice must declare “Return For Repair” and “NO Commercial Value”. The total value of the commercial invoice cannot exceed $10.00USD. If these steps are not followed, the RMA will not be accepted or fulfilled.

Specifications

Material - Bracket, Screws, Nuts:
Polished Stainless Steel
Material - Rail Mount:
Non marring injection molded nylon
Rail Mount Colour:
Black
Rail Size:
7/8" to 1"
Hole Size:
5/8 inch (15.875mm)

Product Reviews

Write Review

This product hasn't received any reviews yet. Be the first to review this product!

Quantity:
SKU:
M-RF1
Condition:
New
Weight:
0.60 LBS
Availability:
Backordered until June. Orders placed will be shipped then.
Shipping:
Calculated at checkout


 

Recent Updates

Connect with us

Newsletter